Home Review Proper Lifting: 8 Commandments to Avoid Injury

Proper Lifting: 8 Commandments to Avoid Injury

Proper lifting technique prevents injuries. Lower, upper, spinal or otherwise, experiencing back pain is practically an aging rite of passage. Four out of five people will experience back pain in their lifetime and, considering sprains and strains are the most common work injury (over 266,000 cases in 2020 alone), it’s not unlikely that injury will occur in the worksite.

So how can you prevent back injuries when lifting, bending and schlepping are all just part of the job? It all starts with proper lifting technique.

HOW TO LIFT HEAVY OBJECTS: SAFE LIFTING TECHNIQUES IN THE WORKPLACE

When performing the common act of proper lifting, there are a handful of simple but important steps workers can take to further reduce the risk of injury. We call them The 8 Commandments.

  1. Plan the lift and test the load
  2. Ask for help if the load in unmanageable
  3. Get a firm footing
  4. Bend at the knees
  5. Tighten the stomach muscles
  6. Lift with your legs (not with your back)
  7. Keep the load close to your body
  8. Keep your back upright
By following the 8 commandments of proper lifting, workers can greatly reduce the likelihood of back pain or injury.

THE HIERARCHY OF CONTROLS: FURTHER MINIMIZING THE RISK OF BACK INJURIES WITH PROPER LIFTING

While proper technique is the backbone of lift injury prevention (pun intended), the entire hierarchy of controls should also be considered to see if the risk can be further reduced before the lift even occurs.

ELIMINATION OR SUBSTITUTION

Start with elimination or substitution. Does the heavy object really need to be lifted or moved? Can the same task be accomplished in a different manner? Can the task be accomplished with a machine or tool as a substitute? While many times the answer is “no”, these questions are the best place to start.

ENGINEERING CONTROLS

If the risk cannot be eliminated or substituted, employers should consider any other controls that might help reduce the risk. This can be as simple as rearranging workstations or processes to reduce lifting, reaching, twisting or bending. When possible, having two individuals perform a task instead of one can greatly improve standard practice. Reduce or eliminate awkward reaches by providing a ladder or step stool, or simply getting physically closer to the task at hand. These are just three examples of controls that can be put in place to lower the risk of sprain and strain injuries.

ADMINISTRATIVE CONTROLS

Beyond elimination, substitution and implementation of engineering controls, workers should be thoroughly trained on the hazard. This of course includes proper lifting technique, as well as conducting job assessments to help workers identify tasks and activities where they are most vulnerable to a strain or sprain. Labeling items with reminders such as “Heavy – Lift with Care” is another effective way to make sure workers take proper precautions. Many injuries occur when workers, especially those that are new to the site, are caught off guard or simply unaware of the risk.

PPE: USING BACK SUPPORTS TO AID IN PROPER LIFTING TECHNIQUE

The last line of defense in the hierarchy of controls is personal protective equipment which, in this case, means back supports. When worn properly, a back support enhances the body’s intra-abdominal pressure and moves stress away from the spine. And, in addition to providing lower back and abdominal support, a back support promotes proper posture and reminds the worker they are about to lift. While back supports can be an incredibly helpful tool in injury prevention, it’s important to note that they do not make workers stronger or cure/eliminate existing injuries.

HOW TO WEAR A BACK SUPPORT

Wearing a back support wrong is like wearing a cracked hard hat or keeping your safety glasses on top of your head—pointless and ineffective. For maximum benefit, back supports need to be properly (and tightly) secured around the midsection.

1. Slip the back support on.

2. Grasp each end of the waistband. Stretch the right end across the left and attach. The upper edge of the waistband should sit approximately 2” (2 finger widths) below your naval. The support should feel snug, but not tight. To test the fit, make sure you can comfortably run a finger between the support and your body.

3. If the support has suspenders, adjust the straps for a comfortable fit without tension.

4. If the support has secondary elastic/tension bands, leave them loosely fastened until it is time to lift. Prior to lifting, grasp these bands and stretch forward as far as possible before securing in a comfortable position.

*Always be sure to read full product instructions before using back and other supports to make sure you are properly fitting and wearing your PPE.

This article republished with permission from Ergodyne.

View our other blog posts related to Personal Protective Equipment.

Most Popular

Comment on Washington state agrees to dismiss meal/rest break appeal by Matthew

The state of Washington agreed last week to dismiss an appeal of a decision that found the state’s truck driver meal and rest break...

Comment on Feds drop fraud charges against Celadon trucking executives by Chris

Federal prosecutors on Wednesday dropped a fraud case alleging two former executives at Celadon Group devised a scheme that cost the truckload and logistics...

Levin on Trump raid: ‘Who lost track of these classified documents?’

NEWYou can now listen to Fox News articles! Mark Levin, host of "Life, Liberty & Levin" reacted to news of the findings in...

Criminal case against Trump Organization and ex-CFO Weisselberg can proceed, judge rules

A New York judge on Friday set an Oct. 24 trial date for the criminal case against the Trump Organization and its former chief...